How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
How do you actually feel on the subject of Installing A Bathtub?
Mounting a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough task. If the old tub is easily obtainable, the project can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. See to it you have actually qualified yourself for the job as well as fit trying it. Rather than hiring a professional to take over a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will help you set up a new tub in your washroom if you have actually already bought a new tub as well as do not require to transform the setup of your previous water pipelines.
Your devices and also product checklist should comprise the following:
Getting ready for the Setup
First of all, the supporting framework supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic as a result of the limited gain access to that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the tub till the level reads level.
To install taps, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has been utilized at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall surface between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback directly below. We'd be interested to know your opinion about this review. Hoping to see you back again later on. In case you enjoyed our blog post if you please remember to pass it around. We treasure reading our article about Tools You Need to Install a New Bathtub .
Visit Homepage Report this page